IPX4, IPX5, IPX6 Combined Water Jet Test Chamber, extremely high pressure water jetting test chamber

IPX6K-Water-Jet-Test-Chamber

IPX4, IPX5, IPX6 Combined Water Jet Test Chamber, extremely high pressure water jetting test chamber

Internal capacity: 800L to 1500L

Model no.: L-RN-IPX6K series

 

Water protection IP Code definition:

  • IPX0: The product offers no special protectionfrom water.
  • IPX1: Can resist water that drips verticallyonto the product.
  • IPX2: Can resist water that hits the product at a 15° angleor less.
  • IPX3: Can take water sprays of up to 60°.
  • IPX4: Is resistant to water splashes from any direction.
  • IPX5: Can resist a sustained, low-pressure water jet spray.
  • IPX6: Can resist high-pressure, heavy spraysof water.
  • IPX6K: Can resist water jets of extremely high pressure. Rarely used.
  • IPX7: Can be submerged up to 1 meterin water for 30 minutes.
  • IPX8: Can be submerged deeper than 1 meter. The exact depth is specified by the manufacturer.

IPX9K: Resists high-pressure, high-temperature sprays at close range. A very special case that’s dictated in ISO20653, Road vehicles — Degrees of protection (IP code) — Protection of electrical equipment against foreign objects, water and access. Rarely used.

IPX6K-Test-Chamber-Nozzles-Turntable

IPX6K-Water-tank-piping

IPX6K-turntable-Speed-control

Specifications for IPX6K High Pressure Water Jetting Test Chamber

Model L-RN-IPX6K-800 L-RN-IPX6K-1000 L-RN-IPX6K-1500
Internal capacity 800L 1000L 1500L
Internal dimension
(W*D*H)mm
1000*800*1000 1000*1000*1000 1000*1500*1000
Water tank dimension
(W*D*H)mm
450*250*450mm 450*350*450mm 450*550*450mm
Nozzle diameter 6.3mm
Water flow rate 75L/min±5%, adjustable
Water pressure 1000kPa
Standard ISO20653
Spray nozzle Spray jet nozzles for IPX6K,
Accessories Equipped with hoses, hand valve, pressurization device,
flow meter, relief valve
Test method High pressure water jet to specimen from 2.5-3m
Test time Min. test duration is 3min.

2.1 Installation site conditions

Install this test chamber in a place which satisfied the following conditions

2.1.1 Ambient conditions
Ambient temperature range: 5~35℃;
Humidity range :           ≤85%RH
Atmospheric pressure:     86~106KPa;
Air quality:    Haven’t high concentration dust and corrosive gas
Floor requirements:    Flat, level floor with good ventilation
Space requirements
For the purpose of future easily ventilation, operation and maintaining, please install the test chamber according to below space requirements:
It needs space more than 800mm from 4 sides of test chamber.
It must have sufficient access space to ensure the door can be opened. Please do not put any objects on the front side of door, as the hot steam may damage the objects.

2.2  Power supply

2.2.1  Power supply
Check main power supply for the equipment (the diameters of electrical wire, power switch etc.) comply with below requirements:
Frequency and fluctuation: 50±0.5Hz;

2.2.2  Ground wire
Connect the test chamber to ground can avoid electric shock and reduce the noise caused by improper running.

2.2.3  Connect power supply cable
Connect the mains power supply cable of test chamber to the external electricity power supply (Check the phase consequence, current, and power consumpation clearly before connection).

3.1 Does your factory has the ability to design according to different specifications?

Yes, we can design the walk in chamber which exactly meet your test requirements, including temperature and humidity, weathering etc.

3.2  In order to get the chamber which meet my requirements, which kind of requirements I should pay attention to?

In order to design the walk in chamber which exact meet your requirements, please let us those requirements at least:

Internal dimension, or specimen dimensions, temperature range, humidity range, ramp rate (if applicable).

3.3 What’s the lead time?

Normally, for a walk in chamber,the lead time is 2 month after deposit received.

3.4 What’s kind of payment method you accepted?

In our factory, the payment term is T/T 30% downpayment before production, and T/T 70% before shipment. If different payment method required, please contact with our sales.

3.5 What’s kind of price term I can work with you?

We accept EXW, FOB Guangdong, CIF destination port.

Related Products